混菌矿化增强再生粗骨料的物理力学性能

为克服单一微生物培养成本高且矿化鲁棒性不足的缺陷，提出了一种混菌矿化增强再生粗骨料物理力学性能的方法.通过筛选矿化效率较高的好氧嗜碱混菌，考察了混菌矿化对再生粗骨料物理力学性能和混凝土抗压强度的影响.结果表明：相同增强时间下，混菌比纯菌呈现出更优异的矿化增强效果；随着混菌矿化增强时间的延长，再生粗骨料吸水率和压碎指标呈现出先减小后增大的趋势，最优增强时间为15 d；采用矿化增强再生粗骨料制备的再生混凝土抗压强度提高幅度达到22.1%.     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.     

LiAlH4–ZrCl4 mixtures for hydrogen release at near room temperature

The dehydrogenation temperature of LiAlH₄ was significantly reduced by the production of mixtures with ZrCl₄. Stoichiometric 4:1, and 5 mol % mixtures of LiAlH₄ and ZrCl₄ were produced by ball milling at room temperature and ?196 °C, and tested for dehydrogenation at low temperature. Cryogenic ball-milling resulted in an effective way to produce reactive mixtures for hydrogen release; because of achieving small aggregates size (5–20 μm) in 10 min of cryomilling while preventing substantial decomposition during preparation. Dehydrogenation reaction in the mixtures LiAlH₄/ZrCl₄ started around 31–47 °C under different heating rates. Partial dehydrogenation was proved at 70 °C: 4.4 wt % for the 5 mol% ZrCl₄–LiAlH₄ mixture, and 3.4 wt % for the best 4:1 stoichiometric mixture. Complete dehydrogenation up to 250 °C released 6.4 wt% and 4.1 wt%, respectively. Dehydrogenation reactions are exothermic, and the LiAlH₄/ZrCl₄ mixtures are unstable and difficult to handle. The activation energy of the exothermic reactions was estimated as 113.5 ± 9.8 kJ/mol and 40.6 ± 6.6 kJ/mol for 4LiAlH₄+ZrCl₄ and 5%mol ZrCl₄+LiAlH₄ samples milled in cryogenic conditions, respectively. The dehydrogenation pathway was changed in the LiAlH₄/ZrCl₄ mixtures as compared to pure LiAlH₄. Dehydrogenation reaction is proposed to form Al, LiCl, Zr, and H₂ as main products. Modification of the dehydrogenation reaction of LiAlH₄ was achieved at the cost of reducing the total hydrogen release capacity.     

Experimental study on mitigating wind erosion of calcareous desert sand using spray method for microbially induced calcium carbonate precipitation

Wind erosion is one of the significant natural calamities worldwide, which degrades around one-third of global land. The eroded and suspended soil particles in the environment may cause health hazards, i.e. allergies and respiratory diseases, due to the presence of harmful contaminants, bacteria, and pollens. The present study evaluates the feasibility of microbially induced calcium carbonate precipitation (MICP) technique to mitigate wind-induced erosion of calcareous desert sand (Thar desert of Rajasthan province in India). The temperature during biotreatment was kept at 36 °C to stimulate the average temperature of the Thar desert. The spray method was used for bioaugmentation of Sporosarcina (S.) pasteurii and further treatment using chemical solutions. The chemical solution of 0.25 pore volume was sprayed continuously up to 5 d, 10 d, 15 d, and 20 d, using two different concentration ratios of urea and calcium chloride dihydrate viz 2:1 and 1:1. The biotreated samples were subjected to erosion testing (in the wind tunnel) at different wind speeds of 10 m/s, 20 m/s, and 30 m/s. The unconfined compressive strength of the biocemented crust was measured using a pocket penetrometer. The variation in calcite precipitation and microstructure (including the presence of crystalline minerals) of untreated as well as biotreated sand samples were determined through calcimeter, scanning electron microscope (SEM), and energy-dispersive X-ray spectroscope (EDX). The results demonstrated that the erosion of untreated sand increases with an increase in wind speeds. When compared to untreated sand, a lower erosion was observed in all biocemented sand samples, irrespective of treatment condition and wind speed. It was observed that the sample treated with 1:1 cementation solution for up to 5 d, was found to effectively resist erosion at a wind speed of 10 m/s. Moreover, a significant erosion resistance was ascertained in 15 d and 20 d treated samples at higher wind speeds. The calcite content percentage, thickness of crust, bulk density, and surface strength of biocemented sand were enhanced with the increase in treatment duration. The 1:1 concentration ratio of cementation solution was found effective in improving crust thickness and surface strength as compared to 2:1 concentration ratio of cementation solution. The calcite crystals formation was observed in SEM analysis and calcium peaks were observed in EDX analysis for biotreated sand.     

The influence of inner material with different average thermal conductivity on the performance of whole insulation system for liquid hydrogen on orbit storage

At present, several composite insulation systems were proposed that can be used for passive insulation systems, including foam-variable density multilayer insulation (VDMLI), aerogel-VDMLI and hollow glass microspheres (HGMs)-VDMLI. The passive insulation systems with different inner material (IM) showed different performances. However, the relationship between the average thermal conductivity of IM and the insulation performance of the whole system has rarely been investigated. It is of great significance for efficient configuration and matching of the passive insulation system. In this paper, a series of average thermal conductivity of IM were assumed to predict the insulation performance of the whole system at 20 K–300 K and high vacuum. In order to further illustrate the relationship between IM and MLI/VDMLI, the foam was replaced by the HGMs as 5 mm a unit forming a series of HGMs-foam-MLI/VDMLI insulation systems. The performance of the systems was investigated. After the foam was completely replaced by the HGMs, the performance of MLI and VDMLI systems was improved 33% and 13%, respectively. Moreover, each mode of heat transfer including solid conduction, radiation, and gas conduction for foam-MLI/VDMLI and HGMs-MLI/VDMLI insulation systems were calculated and analyzed.     

Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Enhancement effect of zero-valent iron nanoparticle and iron oxide nanoparticles on dark fermentative hydrogen production from molasses-based distillery wastewater

This study investigates the effect of two different iron compounds (zero-valent iron nanoparticle: nZVI and iron oxide nanoparticles: nIO) and pH on fermentative biohydrogen production from molasses-based distillery wastewater. The nZVI and nIO of optimum particle sizes of 50 nm and 55 nm respectively were synthesized and applied for fermentative hydrogen (H₂) production. The addition of nIO & nZVI at (0.7 g/L, pH: 6) resulted in the highest H₂ yield, H₂ production rate, H₂ content and COD reduction. Moreover, the kinetic parameters of H₂ production potential (P) and H₂ production rate (R_m) increased to 387 mL, and 22.2 mL/h, respectively for nZVI, these values were 363 mL and 21.8 mL/h for nIO. The results obtained indicated the positive effect of nZVI and nIO addition on enhanced fermentative H₂ production. The addition of nZVI & nIO resulted in 71% and 69.4% enhancement in biohydrogen production respectively.     

The role of Al2O3, MgO and CeO2 addition on steam iron process stability to produce pure and renewable hydrogen

Steam iron process represents a technology for H₂ production based on iron redox cycles. Fe_xO_y are reduced by syngas/carbon to iron, which is subsequently oxidized by steam to produce pure H₂. However, the system shows low stability.In this work, the effect of promoters (Al₂O₃, MgO and CeO₂) on Fe_xO_y stability is investigated (10 consecutive redox cycles). Bioethanol is used as a reducing agent. The particles are synthesized by coprecipitation method, analysed by BET, XRD, SEM and tested in a fixed bed reactor (675 °C, 1 bar). Pure H₂ is obtained controlling the Fe_xO_y reduction degree feeding different amounts of ethanol (4.56–1.14 mmol) until no CO is detected in oxidation. The results show that the promoters not only improve the thermal stability of Fe_xO_y but also affect its redox activity and react with iron forming spinel structures. MgO led to the highest activity and cyclability (H₂ = 0.15 NL; E = 35%).     

Improved photon management in a photoelectrochemical cell with Nd-modified TiO2 thin film photoanode

Photon management involving particularly an up-conversion process is proposed as a relatively novel strategy for improving the efficiency of hydrogen generation in photoelectrochemical cells (PEC) with wide-band gap photoanodes. Optically active photoanode has been constructed by electrodeposition of titanium dioxide nanopowders containing Nd³⁺ ions, synthesized via a sol-gel method, onto ITO/TiO₂(thin film) substrates. Thin films of TiO₂ have been deposited by means of RF magnetron sputtering in an ultra-high-vacuum system. X-ray diffraction, scanning electron microscopy, UV-VIS-NIR spectrophotometry, and photoluminescence have been applied to assess the properties of photoanodes. In experiments involving photon-assisted water splitting, an external up-converter containing Yb³⁺/Er³⁺ rare-earth ions has been used. Photocurrent as a function of voltage (V_B) under illumination with white light is relatively high (280 μA at V_B = 0 V) for pure TiO₂ thin films and it is not affected by the electrodeposition of TiO₂:Nd³⁺ powders. NIR-driven up-conversion with laser excitation at λ = 980 nm has been found responsible for a 13-fold increase in photocurrent at V_B = 0 V in the modified PEC configuration.